ASTM C0140_C0140M-24 - Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
| Standard number: | ASTM C0140_C0140M-24 |
| Released: | 15.06.2024 |
| Status: | Active |
| Pages: | 35 |
| Section: | 04.05 |
| Keywords: | absorption; compressive strength; concrete masonry units; density; equivalent thickness; face shell; moisture content; roof paver; web area; webs; web thickness; |
1.1 These test methods provide various testing procedures commonly used for evaluating characteristics of concrete masonry units and related concrete units. Methods are provided for sampling, measurement of dimensions, compressive strength, absorption, unit weight (density), moisture content, flexural load, and ballast weight. Not all methods are applicable to all unit types, however.
1.2 Specific testing and reporting procedures are included in annexes to these test methods for the following specific unit types:
| Annex A1—Concrete masonry units |
| Annex A2—Concrete and calcium silicate brick |
| Annex A3—Segmental retaining wall units (Specification C1372) |
| Annex A4—Concrete interlocking paving units |
| Annex A5—Concrete grid paving units (Specification C1319) |
| Annex A6—Manufactured concrete ballast units |
| Annex A7—Dry-cast articulating concrete block |
| Annex A8—Segmental and pedestal-set concrete paving slabs |
1.3 The test procedures included in these test methods are also applicable to other types of units not referenced in these test methods, but specific testing and reporting requirements for those units are not included.
1.4 These test methods include the following sections:
|
| Section |
| Scope | 1 |
| Referenced Documents | 2 |
| Terminology | 3 |
| Significance and Use | 4 |
| Sampling | 5 |
| Measurement of Dimensions | 6 |
| Compressive Strength | 7 |
| Absorption | 8 |
| Calculations | 9 |
| Report | 10 |
| Keywords | 11 |
| Annexes—Test Procedures |
|
| Concrete Masonry Units | Annex A1 |
| Concrete and Calcium Silicate Brick | Annex A2 |
| Segmental Retaining | Annex A3 |
| Concrete Interlocking Paving Units | Annex A4 |
| Concrete Grid Paving | Annex A5 |
| Manufactured Concrete Ballast Units | Annex A6 |
| Dry-Cast Articulating | Annex A7 |
| Segmental and Pedestal-Set | Annex A8 |
| Worksheet and Test Report for | Appendix X1 |
| Test Report for Concrete Interlocking | Appendix X2 |
| Calculation of Normalized Web Area | Appendix X3 |
Note 1: The testing laboratory performing these test methods should be evaluated in accordance with Practice C1093.
1.5 The text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.