ASTM D7468-22 - Standard Test Method for Cummins ISM Test
Standard Test Method for Cummins ISM Test
| Standard number: | ASTM D7468-22 |
| Released: | 01.07.2022 |
| Status: | Active |
| Pages: | 36 |
| Section: | 05.04 |
| Keywords: | crosshead wear; Cummins ISM; de-rate protocols; diesel engine oil; exhaust gas recirculation; lubricants; oil filter delta pressure; sludge; top ring mass loss; valve train; |
1.1 The test method covers a heavy-duty diesel engine test procedure conducted under high soot conditions to evaluate oil performance with regard to valve train wear, top ring wear, sludge deposits, and oil filter plugging in an EGR environment. This test method is commonly referred to as the Cummins ISM Test.2
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exception—The only exception is where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing sizes, or where there is a sole source of supply equipment specification.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Annex A1 for general safety precautions.
1.4 Table of Contents:
|
| Section |
| Scope | 1 |
| Referenced Documents | 2 |
| Terminology | 3 |
| Summary of Test Method | 4 |
| Significance and Use | 5 |
| Apparatus | 6 |
| Test Engine Configuration | 6.1 |
| Test Engine | 6.1.1 |
| Oil Heat Exchanger, Adapter Blocks, Block Off Plate | 6.1.2 |
| Oil Filter Head Modification | 6.1.3 |
| Oil Pan Modification | 6.1.4 |
| Engine Control Module (ECM) | 6.1.5 |
| Engine Position Sensor | 6.1.6 |
| Intake Manifold Temperature Sensor | 6.1.7 |
| Barometric Pressure Sensor | 6.1.8 |
| Turbocharger Controller | 6.1.9 |
| Power Supply Voltage | 6.1.10 |
| Air Compressor and Fuel Pump | 6.1.11 |
| Engine Block Preparation | 6.1.12 |
| Test Stand Configuration | 6.2 |
| Engine Mounting | 6.2.1 |
| Intake Air System | 6.2.2 |
| Aftercooler | 6.2.3 |
| Exhaust System | 6.2.4 |
| Exhaust Gas Recirculation System | 6.2.5 |
| Fuel System | 6.2.6 |
| Coolant System | 6.2.7 |
| Pressurized Oil Fill System | 6.2.8 |
| External Oil System | 6.2.9 |
| Crankcase Aspiration | 6.2.10 |
| Blowby Rate | 6.2.11 |
| System Time Responses | 6.3 |
| Oil Sample Containers | 6.4 |
| Mass Balance | 6.5 |
| Engine and Cleaning Fluids | 7 |
| Test Oil | 7.1 |
| Test Fuel | 7.2 |
| Engine Coolant | 7.3 |
| Pentane | 7.4 |
| Solvent | 7.5 |
| Preparation of Apparatus | 8 |
| Cleaning of Parts | 8.1 |
| General | 8.1.1 |
| Engine Block | 8.1.2 |
| Cylinder Head | 8.1.3 |
| Rocker Cover and Oil Pan | 8.1.4 |
| External Oil System | 8.1.5 |
| Crosshead Cleaning and Measurement | 8.1.6 |
| Rod Bearing Cleaning and Measurement | 8.1.7 |
| Ring Cleaning and Measurement | 8.1.8 |
| Injector Adjusting Screw Cleaning and Measurement | 8.1.9 |
| Engine Assembly | 8.2 |
| General | 8.2.1 |
| Parts Reuse and Replacement | 8.2.2 |
| Build-Up Oil | 8.2.3 |
| Coolant Thermostat | 8.2.4 |
| Oil Thermostat | 8.2.5 |
| Fuel Injectors | 8.2.6 |
| New Parts | 8.2.7 |
| Operational Measurements | 8.3 |
| Units and Formats | 8.3.1 |
| Instrumentation Calibration | 8.3.2 |
| Temperatures | 8.3.3 |
| Pressures | 8.3.4 |
| Flow Rates | 8.3.5 |
| Intake and Exhaust CO2 Measurement | 8.3.6 |
| Engine/Stand Calibration and Non-Reference Oil Tests | 9 |
| General | 9.1 |
| New Test Stand | 9.2 |
| New Test Stand Calibration | 9.2.1 |
| Stand Calibration Period | 9.3 |
| Stand Modification and Calibration Status | 9.4 |
| Test Numbering System | 9.5 |
| General | 9.5.1 |
| Reference Oil Tests | 9.5.2 |
| Non-Reference Oil Tests | 9.5.3 |
| Reference Oil Test Acceptance | 9.6 |
| Reference Oil Accountability | 9.7 |
| Last Start Date | 9.8 |
| Donated Reference Oil Test Programs | 9.9 |
| Adjustments to Reference Oil Calibration Periods | 9.10 |
| Procedural Deviations | 9.10.1 |
| Parts and Fuel Shortages | 9.10.2 |
| Reference Oil Test Data Flow | 9.10.3 |
| Special Use of the Reference Oil Calibration System | 9.10.4 |
| Test Procedure | 10 |
| Engine Installation and Stand Connections | 10.1 |
| Coolant System Fill | 10.2 |
| Oil Fill for Break-in | 10.3 |
| Engine Build Committed | 10.3.3 |
| Fuel Samples | 10.4 |
| Engine Warm-up | 10.5 |
| Shutdown During Warm-up | 10.5.1 |
| Engine Break-in | 10.6 |
| Shutdown and Maintenance | 10.7 |
| Normal Shutdown | 10.7.1 |
| Emergency Shutdown | 10.7.2 |
| Maintenance | 10.7.3 |
| Downtime | 10.7.4 |
| 200-h Test Procedure | 10.8 |
| Oil Fill for Test | 10.8.2 |
| Operating Conditions | 10.8.4 |
| Injection Timing Change | 10.8.5 |
| Mass % Soot Validity | 10.8.6 |
| Test Timer | 10.8.7 |
| Operational Data Acquisition | 10.8.8 |
| Oil Sampling | 10.8.9 |
| Oil Addition | 10.8.10 |
| End of Test (EOT) | 10.9 |
| Engine Disassembly | 10.9.3 |
| Calculations, Ratings and Test Validity | 11 |
| Crosshead Mass Loss | 11.1 |
| Crosshead Mass Loss Correction Factor | 11.1.7.1 |
| Injector Adjusting Screw Mass Loss | 11.2 |
| Injector Adjusting Screw Correction Factor | 11.2.5 |
| Ring Mass Loss | 11.3 |
| Sludge Ratings | 11.4 |
| Oil Filter Plugging | 11.5 |
| Oil Analyses | 11.6 |
| Oil Consumption | 11.7 |
| Fuel Analyses | 11.8 |
| Additional Analysis | 11.8.1 |
| Assessment of Operational Validity | 11.9 |
| Assessment of Test Interpretability | 11.10 |
| Test Report | 12 |
| Report Forms | 12.1 |
| Reference Oil Test | 12.2 |
| Electronic transmission of Test Results | 12.2.1 |
| Precision and Bias | 13 |
| Precision | 13.1 |
| Intermediate Precision Conditions | 13.1.1 |
| Reproducibility Conditions | 13.1.2 |
| Bias | 13.2 |
| Keywords | 14 |
| Annexes |
|
| Safety Precautions | Annex A1 |
| Intake Air Aftercooler | Annex A2 |
| Engine Build Parts Kit | Annex A3 |
| Sensor Locations, Special Hardware, and Engine Block Modifications | Annex A4 |
| External Oil System | Annex A5 |
| Cummins Service Publications | Annex A6 |
| Specified Units and Formats | Annex A7 |
| Report Forms and Data Dictionary | Annex A8 |
| Sludge Rating Worksheets | Annex A9 |
| Oil Analyses | Annex A10 |
| Determination of Operational Validity | Annex A11 |
| Exhaust CO2 Sampling Probe | Annex A12 |
| ISM Merit Rating Calculation | Annex A13 |
| Appendix |
|
| Typical System Configurations | Appendix X1 |
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.