BS EN ISO 19085-15:2021 Woodworking Machines. Safety Presses

Ensure the highest standards of safety and efficiency in your woodworking operations with the BS EN ISO 19085-15:2021 standard. This comprehensive document is an essential resource for anyone involved in the woodworking industry, providing detailed guidelines and requirements for the safe operation of woodworking presses.

Key Features

• Standard Number: BS EN ISO 19085-15:2021
• Pages: 58
• Released: 2022-05-23
• ISBN: 978 0 580 98657 4
• Name: Woodworking machines. Safety Presses
• Status: Standard

Comprehensive Safety Guidelines

This standard provides a thorough set of guidelines to ensure the safety of operators and the efficient functioning of woodworking presses. It covers a wide range of safety aspects, including:

• Design and construction requirements
• Safety measures and protective devices
• Operational procedures and maintenance
• Risk assessment and hazard identification

Why Choose BS EN ISO 19085-15:2021?

Adopting the BS EN ISO 19085-15:2021 standard offers numerous benefits:

• Enhanced Safety: Minimize the risk of accidents and injuries by adhering to the latest safety protocols.
• Regulatory Compliance: Ensure your operations meet international safety standards and regulations.
• Operational Efficiency: Improve the efficiency and reliability of your woodworking presses through best practices.
• Industry Recognition: Gain credibility and trust within the woodworking industry by following recognized standards.

Detailed Content

The 58-page document is meticulously organized to provide clear and actionable information. It includes:

• Introduction: Overview of the standard and its objectives.
• Scope: Defines the range of woodworking presses covered by the standard.
• Normative References: Lists other relevant standards and documents.
• Terms and Definitions: Clarifies key terminology used throughout the document.
• Safety Requirements: Detailed guidelines on design, construction, and operational safety.
• Verification of Safety Requirements: Methods for ensuring compliance with the safety guidelines.
• Information for Use: Instructions for safe operation, maintenance, and emergency procedures.

Who Should Use This Standard?

The BS EN ISO 19085-15:2021 standard is invaluable for a wide range of professionals in the woodworking industry, including:

• Manufacturers of woodworking presses
• Safety engineers and consultants
• Quality assurance and compliance officers
• Woodworking shop managers and supervisors
• Maintenance personnel

Stay Ahead with the Latest Standards

In an industry where safety and efficiency are paramount, staying updated with the latest standards is crucial. The BS EN ISO 19085-15:2021 standard represents the cutting edge of safety guidelines for woodworking presses, ensuring that your operations are not only compliant but also optimized for performance.

Conclusion

Investing in the BS EN ISO 19085-15:2021 standard is a proactive step towards enhancing the safety, compliance, and efficiency of your woodworking operations. With its comprehensive guidelines and detailed content, this standard is an indispensable resource for anyone committed to maintaining the highest standards in the woodworking industry.

BS EN ISO 19085-15:2021

This standard BS EN ISO 19085-15:2021 Woodworking machines. Safety is classified in these ICS categories:

• 79.120.10 Woodworking machines
• 13.110 Safety of machinery

This part of ISO 19085 gives the safety requirements and measures for stationary manually loaded and unloaded: - cold presses, - hot presses, - bending presses, - edge/face gluing presses, - membrane presses, - embossing presses, where pressing force is applied by hydraulic actuators pushing two flat or shaped surfaces against each other, hereinafter referred to as "machines". It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE: For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with: - Device for hot gluing - Device for high frequency gluing - Device for high frequency shaping - Automatic work-piece loading and unloading system - intermediate additional platens - work-piece extractor - work-piece clamping pressure beam - split moveable platens. The machines are designed to process work-pieces consisting of: - solid wood; - materials with similar characteristics to wood (see ISO 19085-1:2017, 3.2); - honeycomb. This part of ISO 19085 does not deal with any hazards related to: - specific devices that differ from the list above; - hot fluid heating systems internal to the machine other than electrical; - any hot fluid heating systems external to the machine; - operation of taking intermediate platens out and in again; - the combination of a single machine being used with any other machine (as part of a line). It is not applicable to: - frame presses; - membrane presses where the pressing force is applied by vacuum only; - presses for producing chipboard, fibreboard, OSB; - machines intended for use in potentially explosive atmosphere; - machines manufactured before the date of its publication as an international standard.